7215A REV B Norge Dryer Parts List

Control oven to9 (control oven t09)

This part is also known as the "brains" of the appliance. ***NOTE: The wiring could be different than the original control. This part may need to be installed by an appliance repair person.

Flat beater (beater, flat (powdercoat))

This Flat Beater Part Number WPW10672617 is for Stand Mixers. Attaches to the beater shaft and is for normal to heavy mixtures such as cake batters or cookie dough. This has a powder coated finish.

Water inlet valve - 120v 60hz (water inlet valve)

This water inlet valve is usually located behind the lower kickplate panel in either the right or left corner of the front of your dishwasher. The attaching solenoids on the valve open and close to release the desired amount of water needed in your dishwasher. If your dishwasher is leaking, will not fill with water, is not draining, or not cleaning the dishes properly, you may need to replace the water inlet valve. This valve has 120 volts and 60 Hz. Please be sure to disconnect the power to your dishwasher before starting your repair. This water inlet valve is a genuine OEM part.

Infinite heat switch kit (stove top surface element control switch kit. If the surface element is not heating the element can be tested to determine if it is defective.)

The infinite switch controls the stove top surface burner. This switch will work with most of the electrical range models with coil burner elements.

Single heating element support clip (support bracket for oven broil element.)

The support clip is used to hold the broil element in place at the top of the oven cavity. If the clip is broken or damaged, you will need to replace the part. The support clip is made of metal, is a little over an inch long, and is sold individually. This is a genuine OEM part.

Ice door kit (mechanism)

This ice door is used to seal off the ice chute when not in use. When in use the door will open in the dispenser chute to allow ice to be dispensed. This kit includes the ice door, support, spring, and delay. The heater ribbon is no longer attached. The heater is no longer needed due to an authorized update from the manufacturer. If your ice maker will not dispense ice or frost build up you may need to replace the part. Please remember to disconnect the power to the refrigerator before starting your repair.

Dryer radiant flame sensor (gas dryer sensor)

This part senses if the igniter is hot enough to ignite the flame for heat, allowing the gas valve to open. The sensor is three inches long and is used for many gas clothes dryers. If your dryer is not creating any heat, taking too long to dry or shuts off too soon, you may need to replace the flame sensor. This is a genuine OEM part and is made of both plastic and metal. Please remember to disconnect power to your dryer before starting your repair.

Refrigerator door shelf

This bin can be moved according to space needed. It holds items on the door of your refrigerator. They are sometimes called Cantilever Shelves.

Standard y-frame range surface burner (element (small))

This standard Y-frame 6” surface element is a genuine OEM part that supplies heat to the cooking surface on your range. It has four turns, a black center medallion, looped terminal ends and carries 15000 tts. If your element is not heating, you may need to replace it. Please be sure to disconnect the power to your range before starting your repair. The manufacturer suggests replacing the receptacle at the same time.

Bake element - 240v 2100w (elmnt-bake)

This bake element is a partially open tapered style with push on wire terminals.

Oven bake element (element,bake ,3000w)

The 3000W bake element is located on the bottom of the oven cavity to supply heat for baking. The element terminals are male quarter inch spade connectors and have push-on wire terminals. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. This genuine OEM bake element. Please remember to disconnect the power to your oven before you start your repair.

Door closing cam kit (cam-door)

This door closing cam kit is intended for use with the bottom of refrigerator and freezer door hinges. The cam helps with the closing of the doors and to keep them slightly in position when opened.

Door handle - white (handle door wh)

This part is on the outer door of the dryer.

Refrigerator ice bucket and auger assembly (bucket & auger asm)

Tub spring (tub balancing spring)

This suspension spring is used to support and balance the outer tub of your washer. If the spring is broken it will cause the washer to be noisy and off balance during the spin cycle. Please check your model to see how many springs are required for your model. The spring is sold individually. This is a genuine OEM part. Please make sure you disconnect the power to the washer before starting your repair.